remote control switch

All posts tagged remote control switch

How to Change keyed Rotary Switch to Remote Control Switch?

I am looking to convert a keyed rotary switch with a remote control switch. The switch has 4 positions, position 1 is all Off. Position 2 lower

(turns on compressor) Position 3 Raise (turns on a blower) and Position 4 Drain (turns on a pump). These are turned on individually not all at the same time. The voltage required to power the remote control is AC220V. No current is required to power the devices. The relays are basically open or closed. I would like a 4 channel RF product so I have one channel spare. Can you assist me with what product suits this please.

{S2CIJ`3}[WDS1E7JHMHG0N

According to the descriptions from this customer, we recommend him 4 CH Relay output long range waterproof case wireless remote control kit 0020446 (S4PU-AC220-ANT3+1CB-4). Set the receiver S4PU-AC220-ANT3 with Latched mode, then connect compressor to relay 2 in the receiver, connect blower to relay 3 in the receiver, connect pump to relay 4 in the receiver. This remote control kit is composed of a 4-channel receiver and 4-button transmitter that can be used in agriculture automation, industry automation, and home automation. It can control products on land, water and air, especially in a long distance, such as business signs, motorboat, farm, pasture, offshore unmanned operation, field call, remote security alarm, unmanned aerial vehicle, etc. Connected the compressor to the relay 1 of the 4 CH receiver, connect the blower to relay 2 of the 4 CH receiver, connect the pump to the relay 3 of the 4 CH receiver.

1There are some remarkable characteristics of this 4 CH Relay output long range waterproof case wireless remote control kit.

Waterproof Function: The 4 channel receiver has waterproof connector and waterproof shell/case, so it can be installed outside.

Working Distance: With external telescopic antenna, this remote control kit can have further working distance. The working distance of the kit can reach 2000m in an open ground. If you stretches the external telescopic antenna, it can have a further working range.

Relay Output: The 4 CH receiver is relay output that can be used to operate both DC and AC equipments. The terminal is NO / NC (normally open / normally closed), which serves as a switch. That means you should also connect a separate power supply to it.

Power Output: Each relay output can work at maximum current 30A. The maximum power of the device is 3000W/110V, 6000W/220V. So it also can be used in agriculture and industry automation, such as long range and high power remote control devices.

Input control terminals: The receiver has four input control terminals, you can connect external devices, sensors, or manual switches to these terminals to control the outputs of receiver.

Three Control Modes: The 4 channel receiver has toggle / momentary / latched working control modes. We use latched control for 4 positions keyed rotary switch.

How to set working control mode?

Set toggle control mode (Press -> On; Press again -> Off): Only connect Jumper-2

Set momentary control mode (Press and hold -> On; Release -> Off): Only connect Jumper-1

Set latched control mode (Press -> On, other relays Off; Press other button -> Off): Disconnect Jumper-1 and Jumper-2

IMG_6253We use 3 lamps to instead the compressor, blower and pump. Now let’s change the keyed rotary switch to remote control switch.

Material Preparation:

Receiver: S4PU-AC220-ANT3

Transmitter: CB-4

3 Lamps

A keyed Rotary Switch

Some Lines

材料准备The Wring Diagram:

Just as the following pictures. Connect 3 lamps and 4 positions keyed rotary switch to the 4 Ch receiver. The black wire of the 3 lamps is connected and connect the other black wire to terminal “-“. Connect the red wire of 3 lamps respectively to terminal “A” of relay 1, relay 2 and relay 3. Connect red wire and black wire of the plug respectively to “+” and “-“ of the power. Please note that the red wire used to control lamp1 (compressor) should be connected to terminal A of the relay 1, the red wire used to control lamp2 (blower) should be connected to terminal B of the relay 2, the red wire used to control lamp2 (pump) should be connected to terminal B of the relay 3. The red wire used to turn off the equipments should be connected to terminal B of the relay 3.

 

连线 (2)QQ图片20151113151700

 

Operation:

Press button A of the transmitter, the lamp 1 turns on.

QQ图片20151113151713

Press button B of the transmitter, the lamp 1 turns off and the lamp 2 turns on.

QQ图片20151113151724Press button C of the transmitter, the lamp 2 turns off and the lamp 3 turns on.

QQ图片20151113151734

Press button D of the transmitter, turn off all of the lamps.

QQ图片20151113151743

Online shop: http://www.rfcontrolsystem.com

Share Button

Someone has a question about remote control system he is attempting to build. He has four sensors that give off about 5 volts when activated. When a sensor is activated he wants to transmit a signal to a light and turn on a light.

The basic design is:

Sensor —> Transmitter  –>(Wireless)–> Receiver —> Light What he is  asking is what transmitter could he  use with the 4 Channel Receiver? Would he need 4 separate transmitters for each of the sensors?

sensor

We recommend the low current triggered transmitter (CB-2V) and the ac power direct output receiver (S1X-AC220).

remote controller

The transmitter is triggered by DC power 5~28V input. If low current input triggers transmitter, the transmitter will send RF signal to receiver to indicate it to work. The receiver has 1 Channel AC 110V/220V Power Output terminal contact. He doesn’t have to supply addition power to controlled device because the device will get power from powered receiver.

He can connect his sensor to the transmitter CB-2V, and connect his light to the receiver S1X-A220. Light is connected to L&N terminals of receiver and will get power when the receiver is connected to power supply.

tansmitter circuit

receiver circuit

When a sensor is activated, it can trigger a transmitter to transmit a signal to turn on a light. He needs a separate transmitter for each of sensors.

The transmitter:

http://www.ourautomation.com-p-1551.html

The receiver:

http://www.ourautomation.com/-p-1383.html

Online shop:

http://www.ourautomation.com/1-channel-ac-110v220v-power-output-radio-remote-control-rf-receiver-p-1383.html

Share Button

I am looking for  a remote controller to switch on my computer.  When I press the button on the remote controller, the computer will turn on immediately. So I searched on the internet and found this set of controller is favorable for me. It’s the Model 0020002, S1M-DC12 & C-1. How does it work? Let me show you the simple processing.

This set of remote controller:

The wiring processing is very simple.

Step 1,open the computer and find two wires of switch on computer(see the following picture).

Step 2, Wires should be connected to B&C terminal of the receiver; The receiver should be connected to the power supply.

Step 3, Two wires from B&C terminal of receiver should be soldered to switch wires.

Step 4, Press button, and turn on the computer.

Step 5, Press and hold button for 5 seconds then release, turn off the computer.

Look, that’s so easy wiring processing.

Online shop:

http://www.ourautomation.com/

The model:

http://www.ourautomation.com/1-channel-dc-power-rf-remote-transmitter-receiver-momentary-p-308.html

Share Button

One of our customers says he’d like to use remote control to switch 2 video signals off and on. We recommend him 2 channel dc latching remote control model (S2L-DC12 & C-3)

1

See the following wiring diagram. Two lines of input device (such as camera) is connected respectively to two NO (normally open) terminals C. Two lines of common terminal B is shortened together as a video output line. Then the video output line is connected to the output device (such as computer monitor).

Press remote button C, switch signal to video 1.

Press remote button B, switch signal to video 2.

Press remote button A, switch off the signal.

wiring-diagram

Share Button