One-to-Many Series

This 15 Channel 6V 9V 12V 24V rf remote controller (15S1UB-DC06/09/12/24 & CP-15) is designed to learn remote codes and used in one-transmitter-to-many-receivers system. It operates in toggle, momentary, and latched mode (switching modes as you like freely by connecting or disconnecting jumper). It is great for hard to reach lights or other DC/AC electrical devices with the transmission distance 500m (theoretically). Control lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V. Receiver has DC input contact and you should supply dc power to receiver.

1_011_02

We’d like to show the wiring and controlling of ac, dc lamps or dc motors.

The contact of relay of each receiver is normally open/ closed. So you need to wire ac lamp to normally open contact B&C and supply AC 220V power to lamp. When you want to remote control dc motors or lamps, you can wire them to receivers as mentioned above. But dc motor and lamps can share the same power supply if you wire as the right picture shown.

circuit

Operation:

Setting control mode Toggle: Connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press button 1 again: Turn off Receiver 1 (disconnect B and C, connect A and B)

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press button 15 again: Turn off Receiver 15 (disconnect B and C, connect A and B)

 

Setting control mode Momentary: Connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Release button 1: Turn off Receiver 1 (disconnect B and C, connect A and B)

Press and hold button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Release button 15: Turn off Receiver 15 (disconnect B and C, connect A and B)

 

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 1 (disconnect B and C, connect A and B)

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 15 (disconnect B and C, connect A and B)

Share Button

We recommend this kit-1 Transmitter & 15 Receivers (15S1UB-AC220 & CP-15). It can be applied in controlling lighting, motors, fans, electrically operated doors / locks / windows / blinds / cars or other electric devices with AC 110~240V or DC 0~28V. Its transmission distance is about 500m/1500ft. It has toggle, momentary and latched working modes. You can connect or disconnect jumper to the receiver to switch those working modes. This kit includes 15 receivers and 1 transmitter, so you can connect 15 electric devices to 15 receivers and control electric devices with only one transmitter.

1_01

We’d like to show how to remote control ac, dc lamps or ac motor.

The contact of relay of each receiver is normally open/ closed. So you need to wire dc lamp to normally open contact B&C and supply DC 12V power to lamp. When you want to remote control ac motors or lamps, you can wire them to receivers as mentioned above. But ac motor and lamps can share the same power supply if you wire as the right picture shown.

circuit

Mode switching and operation:

Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press button 1 again: Turn off Receiver 1 (disconnect B and C, connect A and B)

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press button 15 again: Turn off Receiver 15 (disconnect B and C, connect A and B)

 

Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Release button 1: Turn off Receiver 1 (disconnect B and C, connect A and B)

Press and hold button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Release button 15: Turn off Receiver 15 (disconnect B and C, connect A and B)

 

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, another relay Off; Press another button -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 1 (disconnect B and C, connect A and B)

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 15 (disconnect B and C, connect A and B)

Share Button

One of our customers wants a simple wireless remote operate 4 led lamps from several room at his house. He needs 4 transmitters and a receiver which can be mounted in a designated place. The remote must work from receiver about 50m away and not line of sight through doors and walls.

We suggest him choose dc 4 channel remote control system (S4C-DC12& 4C-1). Maximum working current is 5amp each relay. Working distance of remote and receiver set is about 100m (300ft) in open field. This 4CH 6V9V/12V/24V wireless remote switch operates in toggle, momentary, latched, toggle + momentary control mode (set the mode as you like freely). Easy to install and operate. Just press slightly the button on the remote, you can control universal DC/AC electrical devices. The RF signal can pass through walls, doors and other barriers. As he said, we will set 4 transmitters and this receiver with same 8-bits code in advance so that they can work together.

remote controller

Operation modes:

  • 1) Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched (Relay 1~4): Press -> On, other relays Off; Press other button -> Off.

  • 2) Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary (Relay 1~4): Press and hold -> On; Release -> Off.

  • 3) Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle (Relay 1~4): Press -> On; Press again -> Off.

  • 4) Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2.

Control mode Momentary (Relay 1, 2): Press and hold -> On; Release -> Off.

Control mode Toggle (Relay 3, 4): Press -> On; Press again -> Off.

We will show you how to remote control 4 led lamps from different places.

Here is the material.

material

The wiring is a little complicated. Wire lamps to B&C terminals of each relay as wiring diagram shown. Add power supply to led lamps and receiver.

wiring diagram

wiring

Press button of transmitter 1, turn on lamp 1; Press button again, turn off lamp 1.

first lamp

Press button of transmitter 2, turn on lamp 2; Press button again, turn off lamp 2.

second lamp

Press button of transmitter 3, turn on lamp 3; Press button again, turn off lamp 3.

third lamp

Press button of transmitter 4, turn on lamp 4; Press button again, turn off lamp 4.

fourth lamp

Video:

Share Button

This kind of inversion momentary motor controller (S1FM-AC220 & CV-2-2) features in controlling ac motor of rolling blinds/ doors, window cover, projection screens, awnings, water pump, winches, conveyors or other appliances and mechanicals. It can always keep motor running in positive or reversal position if pressing and holding button ▲ or ▼ on remote or receiver. If you release the button, motor will stop. Its transmission distance is about 500m/1500ft theoretically.

transmitter&receiver

We’d like to show you how to wire and control AC motor.

We show prepare the following material:

1×Transmitter (CV-2-2)

1×Receiver (S1FM-AC220)

1×AC Motor

220V Power Supply

Wires

material

At first, we connect live wire to terminal “L” and neutral wire to terminal “N”. Then connect AC motor to terminals “UP”, “COMMOM” and “DOWN”. You can exchange “UP” and “DOWN” wires of motor to change the rotating direction of motor. Add power supply to receiver.

wiring diagram

wiring

Press and hold button ▲ on remote or receiver: Terminals UP and COMMOM directly output AC110V / AC220V; motor rotates continuously in positive direction.

Release button ▲ on remote or receiver: Stop the motor.

positive rotation

Press and hold button ▼ on remote or receiver: Terminals DOWN and COMMOM directly output AC110V / AC220V; motor rotates continuously in reversal direction.

Release button ▼ on remote or receiver: Stop the motor.

reversal rotation

Video:

Share Button

This rf remote controller (12S1UB-DC06/09/12/24 & CV-12 ) has the special ability to learn remote codes, allowing it to be used in one-transmitter-to-many-receivers system. It operates in toggle, momentary, and latched mode (switch modes as you like freely by connecting or disconnecting jumper). It is great for hard to reach lights or other DC/AC electrical devices, remote distance can be 500m (theoretically). Control lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V.

1_011_02

We’d like to show the wiring and controlling of ac, dc lamps or dc motors.

The contact of relay of each receiver is normally open/ closed. So you need to wire ac lamp to normally open contact B&C and supply AC 220V power to lamp. When you want to remote control dc motors or lamps, you can wire them to receivers as mentioned above. But dc motor and lamps can share the same power supply if you wire as the right picture shown.

circuit

Setting control mode Toggle: Connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press button 1 again: Turn off Receiver 1 (disconnect B and C, connect A and B)

Press button 12: Turn on Receiver 12 (connect B and C, disconnect A and B)

Press button 12 again: Turn off Receiver 12 (disconnect B and C, connect A and B)

 

Setting control mode Momentary: Connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Release button 1: Turn off Receiver 1 (disconnect B and C, connect A and B)

Press and hold button 12: Turn on Receiver 12 (connect B and C, disconnect A and B)

Release button 12: Turn off Receiver 12 (disconnect B and C, connect A and B)

 

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 1 (disconnect B and C, connect A and B)

Press button 12: Turn on Receiver 12 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 12 (disconnect B and C, connect A and B)

Share Button

We’d like to recommend one-to-many series: 4 way 6000ft DC RF remote control kit (4S1U-DC12-ANT2 & CB-4), which contains 1 transmitter and 4 receivers. The transmitter’s transmission distance is 2000m/6000ft theoretically with the help of external extended antenna. This wireless gadget can remote control lights, TVs, motors, fans, cameras, video signals, audio signals, electrical operated doors/locks/windows/blinds/cars or other appliances with voltage of AC 110~240V or DC0~28V.

1_011_02

One transmitter can remote control 4 receivers simultaneously. If you want to use two or more receivers in the same place, you can set them with different codes.

For example, we’d like to show how to remote control lamps.

The contact of relay of each receiver is normally open/ closed. So you need to wire lamp to normally open contact B&C and supply DC 12V power to lamp.

1_06

Operation:

Setting control mode Toggle: Connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button A on remote control: Turn on the relay (connect B and C, disconnect A and B)

Press button A again: Turn off the relay (disconnect B and C, connect A and B)

Press button B on remote control: Turn on the relay (connect B and C, disconnect A and B)

Press button B again: Turn off the relay (disconnect B and C, connect A and B)

Setting control mode Momentary: Connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button A on remote control: Turn on the relay (connect B and C, disconnect A and B)

Release button A: Turn off the relay (disconnect B and C, connect A and B)

Press and hold button B on remote control: Turn on the relay (connect B and C, disconnect A and B)

Release button B: Turn off the relay (disconnect B and C, connect A and B)

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button -> Off.

Press button A on remote control: Turn on the relay (connect B and C, disconnect A and B)

Press other button: Turn off the relay (disconnect B and C, connect A and B)

Press button B on remote control: Turn on the relay (connect B and C, disconnect A and B)

Press other button: Turn off the relay (disconnect B and C, connect A and B)

Share Button

We’d like to recommend one-to-many series remote control system: 15 channel remote control system (S15C-DC12 & 15C-1), which includes 15 transmitters and 1 receiver. The transmitter’s transmission distance is 100/300ft theoretically. This wireless gadget can remote control lights, TVs, motors, fans, cameras, video signals, audio signals, electrical operated doors/locks/windows/blinds/cars or other appliances with voltage of AC 110~240V or DC0~28V.

1_011_03

We’d like to show how to wire lamps and remote control lamps with this system.

The initial status is A,B normally open; B,C normally closed. We wire lamps to A&B terminals of each relay one by one. Next, we supply power to receiver. (Supply AC or DC power).

1_07

There are 15 working modes in it. We will try to show you the operation.

1) Learning Momentary control mode: When the receiver is in the status of LEARNING, press transmitter 1.

Control mode Momentary (Channel 1~15): Press and hold -> On; Release -> Off.

Press and hold transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Release transmitter 1: Turn off relay 1 (disconnect A and B, connect B and C)

Press and hold transmitter 15: Turn on relay 15 (connect A and B, disconnect B and C)

Release transmitter 15: Turn off relay 15 (disconnect A and B, connect B and C)

2) Learning Latched control mode: When the receiver is in the status of LEARNING, press transmitter 2.

Control mode Latched (Channel 1~15): Press -> On, other relays Off; Press other button -> Off.

Press transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Turn off other relays (disconnect A and B, connect B and C)

Press transmitter 15: Turn on relay 15 (connect A and B, disconnect B and C)

Turn off other relays (disconnect A and B, connect B and C)

3) Learning Toggle control mode: When the receiver is in the status of LEARNING, press transmitter 3.

Control mode Toggle (Channel 1~15): Press -> On; Press again -> Off.

Press transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Press transmitter 1 again: Turn off relay 1 (disconnect A and B, connect B and C)

Press transmitter 15: Turn on relay 12 (connect A and B, disconnect B and C)

Press transmitter 15 again: Turn off relay 12 (disconnect A and B, connect B and C)

4) Learning Momentary (Channel 1~8) + Latched (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 4.

5) Learning Toggle (Channel 1~8)) + Momentary (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 5l.

6) Learning Latched (Channel 1~8) + Toggle (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 6.

7) Learning Momentary (Channel 1~13) + Latched (Channel 14~15) control mode: When the receiver is in the status of LEARNING, press transmitter 7.

8) Learning Toggle (Channel 1~13) + Momentary (Channel 14~15) control mode: When the receiver is in the status of LEARNING, press transmitter 8.

9) Learning Toggle (Channel 1~5) + Momentary (Channel 6~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 9.

10) Learning Momentary (Channel 1~5) + Latched (Channel 6~10) + Momentary (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 10.

11) Learning Toggle (Channel 1~2) + Momentary (Channel 3~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 11.

12) Learning Momentary (Channel 1~2) + Toggle (Channel 3~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 12.

13) Learning Latched (Channel 1~2) + Momentary (Channel 3~10) + Toggle (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 13.

14) Learning Toggle (Channel 1~2) + Latched (Channel 3~9) + Momentary (Channel 10~15) control mode: When the receiver is in the status of LEARNING, press transmitter 14.

15) Learning Toggle (Channel 1~13) + All On / Off (Channel 14/15): When the receiver is in the status of LEARNING, press butt transmitter on 15.

Press transmitter 14: Turn on all 15 relays

Press transmitter 15: Turn off all 15 relays

Share Button

Question from customer:

Whether we can get the receivers with different voltage versions? For example 2 piece of 24 volt and 2 piece of 240 volt.

Answer:

Yes, it is possible. We recommend those two kinds of receivers—for 24V version, it is 24V DC input receiver (S2UB-DC24). For 240V version, it is 100V~240V input receiver (S2U-AC220). Both of them have two relays on the PCB. So there are four channels totally for your devices. They can pair up with long range transmitter (CB-4).

remote-controller

It can control lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances with voltage AC 110~240V or DC 0~28V. Owing to normally open& closed contact, you should add additional power supply to your devices besides your receivers. But you can do as following wiring method to save power supply adaptors. Wire devices (lamps) to B terminals of each relay, using wires to connect devices to output terminals of each receiver. For dc input receiver, we supply dc 24v power; for ac input receiver, we supply ac 240v power.

circuit

There are toggle, momentary, latched and momentary+toggle modes. You want to remote control 4 devices, so you’d better choose toggle or momentary mode or toggle+momentary mode.

Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button A: Turn on relay 1 of Receiver 1 (connect B and C, disconnect A and B)

Press button A again: Turn off relay 1 of Receiver 1 (disconnect B and C, connect A and B)

Press button D: Turn on relay 2 of Receiver 2 (connect B and C, disconnect A and B)

Press button D again: Turn off relay 2 of Receiver 2 (disconnect B and C, connect A and B)

Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button A: Turn on relay 1 of Receiver 1 (connect B and C, disconnect A and B)

Release button A: Turn off relay 1 of Receiver 1 (disconnect B and C, connect A and B)

Press and hold button D: Turn on relay 2 of Receiver 2 (connect B and C, disconnect A and B)

Release button D: Turn off relay 2 of Receiver 2 (disconnect B and C, connect A and B)

Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2.

Control mode Momentary (Channel 1 of Receiver 1, 2): Press and hold -> On; Release -> Off.

Press and hold button A: Turn on relay 1 of Receiver 1 (connect B and C, disconnect A and B)

Release button A: Turn off relay 1 of Receiver 1 (disconnect B and C, connect A and B)

Press and hold button B: Turn on relay 1 of Receiver 2 (connect B and C, disconnect A and B)

Release button B: Turn off relay1 of Receiver 2 (disconnect B and C, connect A and B)

Control mode Toggle (Channel 2 of Receiver 1, 2): Press -> On; Press again -> Off.

Press button C: Turn on relay 2 of Receiver 1 (connect B and C, disconnect A and B)

Press button C again: Turn off relay 2 of Receiver 1 (disconnect B and C, connect A and B)

Press button D: Turn on relay 2 of Receiver 2 (connect B and C, disconnect A and B)

Press button D again: Turn off relay 2 of Receiver 2 (disconnect B and C, connect A and B)

Share Button

This kind of remote control gadget (12S1XB-DC12-ANT2+CB-12) is actuated by 4 voltages, including DC 6V, 9V, 12V, 24V. It has DC power output contact, that is to say, you don’t have to supply additional power to the device to be controlled. To extend controlling range to 1000m, we solder external extended antenna to PCB. This kit includes one 12-channel transmitter and 12 receivers and they are programmed the same code so that they can work together.

remote control kit-our automation

It can control lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances. For instance, we try to remote control dc lamps. Wire each lamp to A&B terminals of each receiver.

wiring diagram-our automation

There are three control modes, including toggle, momentary and latched.

To remote control 12 lamp, toggle mode is much better.

Setting control mode Toggle: Only connect Jumper-2.

Press button 1: Turn on the relay, terminal A&B of receiver 1 outputs DC power.

Press button 1 again: Turn off the relay, terminal A&B of receiver 1 no output.

Press button 12: Turn on the relay, terminal A&B of receiver 12 outputs DC power.

Press button 12 again: Turn off the relay, terminal A&B of receiver 12 no output.

 

You also can set latched mode.

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Press button 1: Turn on the relay, terminal A&B of receiver 1 outputs DC power.

Press other buttons: Turn off the relay, terminal A&B of receiver 1 no output.

Press button 12: Turn on the relay, terminal A&B of receiver 12 outputs DC power.

Press other buttons: Turn off the relay, terminal A&B of receiver 12 no output.

Share Button

99-channel Transmitter pairs up with 24 receivers to build a remote control kit (24S1XCB-AC220 & CP-99). It can controls lights, fans, motors, electrically actuated doors/ locks/ windows/ rolling blinds/ cars or other appliance with AC 110~240V. The transmitter adopts singlechip technology to build million of code and has LCD display screen. One transmitter can work with 99 receivers simultaneously.

remote controller-our automation1_10

This kind of remote controller aims at controlling 24 AC Lamps. We will show you the procedure.

circuit-our automation

circuit-diagram

Step 1

Wire each lamp to terminals 1 &5 of each receiver. And supply power to each receiver.

Step 2

The coding type is learning code, so receiver should learn from transmitter at first.

1) Press and hold the button of receiver about 2 seconds until signal LED flashes; then release the button, at this time the receiver enters into status of LEARNING.

2) Press any number button on the transmitter to select a number from 01 to 99, then press button “T” or “M” to send signal. If signal LED immediately turns off, it means learning is successful.

3) The receiver can learn only one channel of the transmitter. So learning code must be one by one till the last one.

Step 3

Press any number button to select a number from 01 to 99 by combination of the number 0~9, then press button “T” (Toggle) or “M” (Momentary) to send signal. LCD screen will displays numbers at the same time, and LCD screen will turn off after 15 seconds if there is no any operation.

Toggle Mode Operation: If you want to send signal of the 24 channel, you can press “2”, then press “4”, next press button “T”, the signal is sent immediately; when you press the button “T” again, the signal will be sent again.

Momentary Mode Operation: If you want to send signal of the 24 channel, you can press “2”, then press “4”, next press and hold button “M”, the signal is continuously sent; when you release the button “M”, the signal will stop.

So we want to remote control 24 AC lamps, we choose Toggle mode.

Press 1+T, send signal to receiver, turn on lamp 1, press T again, turn off lamp 1. (Waiting for LCD screen being off, you can continue next operation every time.)

Press 2+4+T, send signal to receiver, turn on lamp 24, press T again, turn off lamp 24.

 

Share Button